iPhone 8+ Battery Replacement

Introduction
Use this guide to revive your iPhone 8 Plus with a new battery.

This guide instructs you to fully detach the display assembly; this is intended to prevent accidental damage to the display cables. If you feel comfortable removing the battery without putting undue strain on the display cables, you can skip the steps for detaching the display. Additionally, while it’s possible to remove the adhesive strips securing the battery as soon as you open the phone, this guide recommends first removing the Taptic Engine. Doing so reduces the risk of breaking the lower adhesive strips accidentally, either by snagging them on the Taptic Engine, or by pulling the strips at too sharp of an angle.

For optimal performance after completing this guide, calibrate your newly installed battery: Drain it below 10%, then charge it uninterrupted to 100%.

Tools
Buy these tools

Standoff Screwdriver for iPhones
P2 Pentalobe Screwdriver iPhone
iOpener
iSclack
Suction Handle
iFixit Opening Picks set of 6
iFixit Opening Tools
Phillips #000 Screwdriver
Tri-point Y000 Screwdriver Bit
Tweezers
Spudger
Parts
Buy these parts


iPhone 8 Plus Replacement Battery

$49.99

Buy
iPhone 8 Plus Battery Adhesive Strips
iPhone 8 Plus Display Assembly Adhesive
iPhone 8/8 Plus Bottom Screws
Video Overview


Step 1 Pentalobe Screws
Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

Power off your iPhone before beginning disassembly.

Remove the two 3.5 mm pentalobe screws from the bottom edge of the iPhone.

Opening the iPhone's display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 2 Opening Procedure
Heating the lower edge of the iPhone will help soften the adhesive securing the display, making it easier to open.
Heating the lower edge of the iPhone will help soften the adhesive securing the display, making it easier to open.

Use a hairdryer or prepare an iOpener and apply it to the lower edge of the iPhone for about 90 seconds in order to soften up the adhesive underneath.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 3
Apply a suction cup to the lower half of the front panel, just above the home button.


Apply a suction cup to the lower half of the front panel, just above the home button.

Be sure the suction cup does not overlap with the home button, as this will prevent a seal from forming between the suction cup and front glass.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 4
Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.



Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.

Insert an opening pick or other thin pry tool a few millimeters into the gap.

The watertight adhesive holding the display in place is very strong; creating this initial gap takes a significant amount of force. If you're having a hard time opening a gap, apply more heat, and gently rock the screen up and down to weaken the adhesive until you create enough of a gap to insert your tool.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 5
Slide your pick around the corner and up the left edge of the phone, moving towards the volume control buttons and silent switch, breaking up the adhesive holding the display in place.



Slide your pick around the corner and up the left edge of the phone, moving towards the volume control buttons and silent switch, breaking up the adhesive holding the display in place.

Stop near the top left corner of the display.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 6
Re-insert your tool at the lower right corner of the iPhone, and slide it around the corner and up the right side of the phone to separate the adhesive.



Re-insert your tool at the lower right corner of the iPhone, and slide it around the corner and up the right side of the phone to separate the adhesive.

Don't insert the pick very far, or you may damage the display cables along this side of the iPhone. Insert it only a few millimeters, or about the width of the display bezel.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 7
Gently pull up on the suction cup to lift up the bottom edge of the display.
Gently pull up on the suction cup to lift up the bottom edge of the display.

Do not raise the display more than 15º or you'll risk straining or tearing the ribbon cables connecting the display.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 8
Pull on the small nub on the suction cup to remove it from the front panel.
Pull on the small nub on the suction cup to remove it from the front panel.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 9
Slide an opening pick underneath the display along the top edge of the phone to loosen the last of the adhesive.



Slide an opening pick underneath the display along the top edge of the phone to loosen the last of the adhesive.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 10
Slide the display assembly slightly down (away from the top edge of the phone) to disengage the clips holding it to the rear case.


Slide the display assembly slightly down (away from the top edge of the phone) to disengage the clips holding it to the rear case.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 11
Open the iPhone by swinging the display up from the left side, like the back cover of a book.



Open the iPhone by swinging the display up from the left side, like the back cover of a book.

Don't try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone's logic board.

Lean the display against something to keep it propped up while you're working on the phone.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 12 Battery Disconnection
Remove four Phillips (JIS) screws securing the lower display cable bracket to the logic board, of the following lengths:

TOOLS USED ON THIS STEP:
Magnetic Project Mat $19.99


Remove four Phillips (JIS) screws securing the lower display cable bracket to the logic board, of the following lengths:

Two 1.3 mm screws

One 1.4 mm screw

One 2.7 mm screw

Throughout this guide, keep careful track of your screws so that each one goes back where it came from during reassembly. Installing a screw in the wrong place can cause permanent damage.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)



Answers
We are a community of people helping each other fix stuff.
Come hang out with us.
Answers Forum
Step 13
Remove the lower display cable bracket.
Remove the lower display cable bracket.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 14
Use the point of a spudger to pry the battery connector up from its socket on the logic board.


Use the point of a spudger to pry the battery connector up from its socket on the logic board.

Bend the connector cable up slightly to prevent it from accidentally making contact with the socket and providing power to the phone during your repair.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 15 Display Assembly
Use the tip of a spudger or a fingernail to disconnect the large lower display connector by prying it straight up from its socket.


Use the tip of a spudger or a fingernail to disconnect the large lower display connector by prying it straight up from its socket.

To re-attach press connectors like this one, press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is even slightly misaligned, the connector can bend, causing permanent damage.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 16
Disconnect the second lower display cable connector, directly behind the one you disconnected in the previous step.


Disconnect the second lower display cable connector, directly behind the one you disconnected in the previous step.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 17
Remove the two tri-point Y000 screws securing the bracket over the front panel sensor assembly connector:


Remove the two tri-point Y000 screws securing the bracket over the front panel sensor assembly connector:

One 1.0 mm screw

One 1.2 mm screw

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 18
Remove the bracket covering the front panel sensor assembly connector.
Remove the bracket covering the front panel sensor assembly connector.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 19
Use the tip of a spudger or a fingernail to disconnect the front panel sensor assembly connector from its socket.


Use the tip of a spudger or a fingernail to disconnect the front panel sensor assembly connector from its socket.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 20
Remove the display assembly.
Remove the display assembly.

During here reassembly, pause here if you wish to replace the adhesive around the edges of the display.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 21 Wi-Fi Diversity Antenna
Remove the three screws securing the L-shaped bracket next to the Taptic Engine:


Remove the three screws securing the L-shaped bracket next to the Taptic Engine:

One 1.3 mm Y000 screw

One 2.6 mm Phillips screw

One 3.5 mm Phillips screw

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 22
Remove the bracket.
Remove the bracket.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 23
Use an opening pick to gently separate the adhered portion of the antenna flex cable from the top surface of the speaker.



Use an opening pick to gently separate the adhered portion of the antenna flex cable from the top surface of the speaker.

This portion of the flex cable is lightly adhered in place. If necessary, apply a little heat from an iOpener or hair dryer to soften the adhesive. This makes it easier to separate (and re-adhere) the flex cable safely.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 24
Use the point of a spudger to pry up and disconnect the antenna flex cable from the logic board.


Use the point of a spudger to pry up and disconnect the antenna flex cable from the logic board.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 25
Use the point of your spudger to pry up and disconnect the other end of the antenna flex cable from its socket, next to the Lightning Port.



Use the point of your spudger to pry up and disconnect the other end of the antenna flex cable from its socket, next to the Lightning Port.

Reconnecting this cable can be tricky. Make it easier by using your tweezers to hold the flex cable so the connector aligns with its socket. Then, gently press down on the connector with the flat of your spudger until it clicks into place.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 26
Remove the Wi-Fi diversity antenna.
Remove the Wi-Fi diversity antenna.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 27 Taptic Engine
Remove the three screws securing the Taptic Engine:


Remove the three screws securing the Taptic Engine:

Two 1.5 mm Phillips screws

One 2.4 mm standoff screw

Standoff screws are best removed using an iPhone Standoff Screwdriver Bit and driver handle.

In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 28
Use the point of your spudger to pry up and disconnect the Taptic Engine flex cable.


Use the point of your spudger to pry up and disconnect the Taptic Engine flex cable.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 29
Remove the Taptic Engine.
Remove the Taptic Engine.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 30 Battery
The iPhone 8 Plus's battery is secured by four pieces of stretch-release adhesive—two at the top, and two at the bottom.
The iPhone 8 Plus's battery is secured by four pieces of stretch-release adhesive—two at the top, and two at the bottom.

Each piece of adhesive has a black pull-tab at the end, which is lightly adhered to the front surface of the battery.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 31
Peel back the first battery adhesive tab from the bottom right edge of the battery.



Peel back the first battery adhesive tab from the bottom right edge of the battery.

If possible, use your fingernails or blunt tweezers. Be careful not to poke the battery with any sharp tools.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 32
Try to keep the adhesive strips flat and unwrinkled during this procedure; twisted or wrinkled strips will stick together and break instead of pulling out cleanly.



Try to keep the adhesive strips flat and unwrinkled during this procedure; twisted or wrinkled strips will stick together and break instead of pulling out cleanly.

Additionally, do not press down on the battery as you pull the strips. Pressing on the battery creates pressure points that can snag and break the adhesive.

Slowly pull one battery adhesive tab away from the battery, towards the bottom of the iPhone.

Pull steadily, maintaining constant tension on the strip until it slips out from between the battery and the rear case. For best results, pull the strip at as low an angle as possible, without snagging it on any of the iPhone's other components.

The strip will stretch to many times its original length. Continue pulling and re-grab the strip near the battery if necessary.

If the battery adhesive tabs break during the removal process, use your fingers or blunt tweezers to retrieve the remaining length of adhesive, and continue pulling.

If any of the adhesive strips break underneath the battery and cannot be retrieved, try to remove the remaining strips, and then proceed as instructed below.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 33
Repeat the above steps to remove the remaining three adhesive strips.


Repeat the above steps to remove the remaining three adhesive strips.

Be sure to hold onto the battery as you remove the final strip, or it may fling out of the iPhone unexpectedly.

If you removed all of the adhesive strips successfully, skip the next step.

If any of the adhesive strips broke off underneath the battery and could not be retrieved, continue with the next step below.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 34
If any of the adhesive strips broke off and the battery remains stuck to the rear case, prepare an iOpener or use a hair dryer to heat the rear case directly behind the battery. This will help soften the adhesive.


If any of the adhesive strips broke off and the battery remains stuck to the rear case, prepare an iOpener or use a hair dryer to heat the rear case directly behind the battery. This will help soften the adhesive.

Heat the iPhone until the rear case is slightly too hot to comfortably touch. Don't overheat the iPhone, or you may accidentally ignite the battery.

Flip the iPhone back over and thread a strong piece of string (such as dental floss or a length of thin guitar string) underneath the battery.

Pull the string from side to side in a sawing motion all along the length of the battery to separate the adhesive. Do not deform or damage the battery.

To protect your fingers, wear gloves or wrap the string ends around a tool (such as the two screwdriver handles shown in the image).

If you choose to use pry tools to lift the battery out of the iPhone, use extreme caution or you may damage the ribbon cables or the wireless charging coil directly underneath the battery.

Add a comment
Bold (ctrl+b)Italic (ctrl+i)Insert a link (ctrl+k)Insert a quoteUndo (ctrl+z)Redo (ctrl+⇧z)


Step 35
Remove the battery from the iPhone.
Remove the battery from the iPhone.

If your replacement battery came in a plastic sleeve, slide off and remove the sleeve before installation.

When installing the battery, refer to this guide to replace your battery's adhesive strips.

Perform a force restart after reassembly. This can prevent several issues and simplify troubleshooting.

Leave a Reply

Your email address will not be published. Required fields are marked *